Difference between revisions of "Robot Files and Project Files"
From Wiki
| Line 6: | Line 6: | ||
|- | |- | ||
! Igus robolink DQ arm or Igus robolink D arm? | ! Igus robolink DQ arm or Igus robolink D arm? | ||
| − | |<IGUS_DQ_arm/IGUS_arm>| | + | |<IGUS_DQ_arm/IGUS_arm>|| There are several types or robolink robot arms, the most common is the D arm, named just “IGUS arm” || [[file:igus_d_dq.png|200px|frameless]] |
| − | | There are several types or robolink robot arms, the most common is the D arm, named just “IGUS arm” || [[file:igus_d_dq.png|200px|frameless]] | ||
|- | |- | ||
! 4 DOF or 5 Glossary? | ! 4 DOF or 5 Glossary? | ||
| − | |<4DOF/5DOF>| | + | |<4DOF/5DOF>|| DOF is the acronym for “degrees of freedom”, meaning the number of robot joints. The robot on the right is 5 DOF. Note: the white gripper is not counted.|| [[file:robolink_DOF.png|200px|frameless]] |
| − | | DOF is the acronym for “degrees of freedom”, meaning the number of robot joints. The robot on the right is 5 DOF. Note: the white gripper is not counted.|| [[file:robolink_DOF.png|200px|frameless]] | ||
|- | |- | ||
!BV or SV? | !BV or SV? | ||
| − | |<SV/BV>| | + | |<SV/BV>|| BV stands for Big Version with 2.5 kg payload. SV stands for Small Version with 0.5 kg payload. Measure the diameter of joint 2. 5cm = BV; 3cm = SV || [[file:robolink_BVSV.png|200px|frameless]] |
| − | | BV stands for Big Version with 2.5 kg payload. SV stands for Small Version with 0.5 kg payload. Measure the diameter of joint 2. 5cm = BV; 3cm = SV || [[file:robolink_BVSV.png|200px|frameless]] | ||
|- | |- | ||
! AE or ME? | ! AE or ME? | ||
| − | |<AE/ME>| | + | |<AE/ME>||ME versions use a motor encoder, AE version use a encoder on the gear output. Count the number of sockets of any of the modules labelled "Stepper Motor Driver Module" on the DIN Rail. 4 sockets = ME; 3 sockets = AE ||[[file:DINrail_AEME.png|200px|frameless]] |
| − | |ME versions use a motor encoder, AE version use a encoder on the gear output. Count the number of sockets of any of the modules labelled "Stepper Motor Driver Module" on the DIN Rail. 4 sockets = ME; 3 sockets = AE ||[[file:DINrail_AEME.png|200px|frameless]] | ||
|} | |} | ||
== | == | ||
Revision as of 21:08, 13 May 2018
The name of the configuration file that you need to use in CPRog for your robot is composed as follows. Use the table below to identify the
filename:
In general, any configuration file is comprised like this <#><IGUS_DQ_arm/IGUS_arm>_<4DOF/5DOF>_<SV/BV>_<AE/ME>.prj
| Igus robolink DQ arm or Igus robolink D arm? | <IGUS_DQ_arm/IGUS_arm> | There are several types or robolink robot arms, the most common is the D arm, named just “IGUS arm” | 
|
|---|---|---|---|
| 4 DOF or 5 Glossary? | <4DOF/5DOF> | DOF is the acronym for “degrees of freedom”, meaning the number of robot joints. The robot on the right is 5 DOF. Note: the white gripper is not counted. | 
|
| BV or SV? | <SV/BV> | BV stands for Big Version with 2.5 kg payload. SV stands for Small Version with 0.5 kg payload. Measure the diameter of joint 2. 5cm = BV; 3cm = SV | 
|
| AE or ME? | <AE/ME> | ME versions use a motor encoder, AE version use a encoder on the gear output. Count the number of sockets of any of the modules labelled "Stepper Motor Driver Module" on the DIN Rail. 4 sockets = ME; 3 sockets = AE | 
|
==
