Difference between revisions of "Troubleshooting Identification"

From Wiki
Line 27: Line 27:
 
## [[Troubleshooting_Recovery#Reset_and_Enable|Reset and Enable]]
 
## [[Troubleshooting_Recovery#Reset_and_Enable|Reset and Enable]]
 
## [[Troubleshooting_Recovery#Broken_Connections|Broken Connections]]
 
## [[Troubleshooting_Recovery#Broken_Connections|Broken Connections]]
−
## [[Troubleshooting_Recovery#Reverse_Encoder_Direction|Reverse ## [[Troubleshooting_Recovery#Check_Motor_Bridge|Check Motor Bridge]]
+
## [[Troubleshooting_Recovery#Reverse_Encoder_Direction|Reverse]]
 +
## [[Troubleshooting_Recovery#Check_Motor_Bridge|Check Motor Bridge]]
  
 
== FAQ - Standard Cases during Operation ==
 
== FAQ - Standard Cases during Operation ==
  
 
# Strong breaking noise when a joint accelerates, joint stops with error "LAG" or "ENC"
 
# Strong breaking noise when a joint accelerates, joint stops with error "LAG" or "ENC"
−
 
+
## [[Troubleshooting_Recovery#Motor_Stall|Motor Stall]]
 
# Motor is too hot (> 80 Deg. C)
 
# Motor is too hot (> 80 Deg. C)
 +
## [[Troubleshooting_Recovery#Motor_Overheating|Motor Overheating]]
 +
# Robot stops with Error Code "EStop / Temp"
 +
## [[Troubleshooting_Recovery#Release_Emergency_Stop|Release E-Stop]]
 +
## [[Troubleshooting_Recovery#Fan_Malfunction|Fan Malfunction]]
 +
## [[Troubleshooting_Recovery#Electronics_Overheating|Electronics Overheating]]
 +
# Squeaking sound when the joint moves
 +
## [[Troubleshooting_Recovery#Add_Lubricant|Add Lubricant]]
  
−
# Squeaking sound when the joint moves
 
  
  
Line 41: Line 48:
 
== Mechanics / Cables ==
 
== Mechanics / Cables ==
 
# Motor does not turn
 
# Motor does not turn
−
 
+
## [[Troubleshooting_Recovery#Reset_and_Enable|Reset and Enable]]
 +
## [[Troubleshooting_Recovery#Load_Correct_Project|Load Correct Project ]]
 +
## [[Troubleshooting_Recovery#Broken_Connections|Broken Connections]]
 +
## [[Troubleshooting_Recovery#Release_Emergency_Stop|Release E-Stop]]
 +
## [[Troubleshooting_Recovery#Reset_and_Enable|Reset and Enable]]
 +
## [[Troubleshooting_Recovery#Check_Power_Supply|Check Power Supply]]
 
# Motor starts to turn, gets faster and does not stop
 
# Motor starts to turn, gets faster and does not stop
−
 
+
## [[Troubleshooting_Recovery#Reverse_Encoder_Direction|Reverse Encoder Direction]]
 
# Joint does not move continually
 
# Joint does not move continually
−
 
+
## [[Troubleshooting_Recovery#Loose_Clutch|Loose Clutch]]
 +
## [[Troubleshooting_Recovery#Replace_Gear|Replace Gear]]
 
# Referencing does not terminate
 
# Referencing does not terminate
−
 
+
## [[Troubleshooting_Recovery#Reduce_Sensor_Distance|Reduce Sensor Distance]]
 +
## [[Troubleshooting_Recovery#Referencing_Joint5|Referencing Joint5]]
 
# Referencing inconsistent
 
# Referencing inconsistent
 +
## [[Troubleshooting_Recovery#Reduce_Sensor_Distance|Reduce Sensor Distance]]
  
−
#
 
  
 
== Electronics ==
 
== Electronics ==
Line 67: Line 81:
  
 
# Robot does not move in a straight line
 
# Robot does not move in a straight line
 +
## [[Troubleshooting_Recovery#|]]
  
 
#Second DIO not working
 
#Second DIO not working
−
[[Troubleshooting_Recovery#10.5_Wrong_CAN_ID|Wrong CAN ID]]
+
## [[Troubleshooting_Recovery#10.5_Wrong_CAN_ID|Wrong CAN ID]]
  
 
== Programming ==
 
== Programming ==

Revision as of 22:29, 8 March 2020

Back to Troubleshooting...

FAQ - Standard Problems during Setup

  1. Joints do not move at all:
    1. Release E-Stop,
    2. Reset and Enable,
    3. Check Power Supply,
  2. A5 moves fast and does not stop
    1. Reverse Encoder Direction
  3. False motion directions
    1. Load Correct Project
  4. Strange XYZ coordinates
    1. Load Correct Project
    2. Define Zero Positions
  1. Joint is moveable by hand with no electrical power applied
    1. Loose Clutch
    2. Replace Gear
  1. Position lag "LAG" error
    1. Reset and Enable
    2. Broken Connections
    3. Reverse Encoder Direction
    4. Check Motor Bridge
  1. Encoder "ENC" error
    1. Reset and Enable
    2. Broken Connections
    3. Reverse
    4. Check Motor Bridge

FAQ - Standard Cases during Operation

  1. Strong breaking noise when a joint accelerates, joint stops with error "LAG" or "ENC"
    1. Motor Stall
  2. Motor is too hot (> 80 Deg. C)
    1. Motor Overheating
  3. Robot stops with Error Code "EStop / Temp"
    1. Release E-Stop
    2. Fan Malfunction
    3. Electronics Overheating
  4. Squeaking sound when the joint moves
    1. Add Lubricant



Mechanics / Cables

  1. Motor does not turn
    1. Reset and Enable
    2. Load Correct Project
    3. Broken Connections
    4. Release E-Stop
    5. Reset and Enable
    6. Check Power Supply
  2. Motor starts to turn, gets faster and does not stop
    1. Reverse Encoder Direction
  3. Joint does not move continually
    1. Loose Clutch
    2. Replace Gear
  4. Referencing does not terminate
    1. Reduce Sensor Distance
    2. Referencing Joint5
  5. Referencing inconsistent
    1. Reduce Sensor Distance


Electronics

  1. Error "Module Dead"

Wrong CAN ID

  1. No LED on the module is on

Check Power Supply

  1. Display shows jitter

Wrong CAN ID


Configuration

  1. Robot does not move in a straight line
    1. [[Troubleshooting_Recovery#|]]
  1. Second DIO not working
    1. Wrong CAN ID

Programming

Retrieved from "http://wiki.cpr-robots.com/index.php?title=Troubleshooting_Identification&oldid=2323"